| | |
Insta Cure Cyano 1/2oz bottle (14.2g)(Reference #1889)
INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
Price: £2.12 £2.44 Including VAT at 15%
|  |
|
 |
INSTA-CURE+™ Gap Filling - 1/2oz bottle (14.2g)(Reference #2317)
is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
Price: £2.13 £2.45 Including VAT at 15%
|  |
|
|
INSTA-CURE+™ Gap Filling - 1oz bottle (28.4)(Reference #2318)
As above but 1oz quantity
Price: £3.83 £4.40 Including VAT at 15%
| |
|
|
SUPER-GOLD Thin™ 1/2oz bottle (14.2g)(Reference #2319)
ODORLESS INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
Price: £3.74 £4.30 Including VAT at 15%
|  |
|
|
SUPER-GOLD+™ Gap Filling 1/2oz (14.2g(Reference #2321)
ODORLESS INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
Price: £3.74 £4.30 Including VAT at 15%
|  |
|
|
INSTA-SET™ (Reference #2323)
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
Price: £2.99 £3.44 Including VAT at 15%
|  |
|
|
UN-CURE™ 1oz (28.4g) bottle(Reference #2324)
debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.
Price: £1.92 £2.21 Including VAT at 15%
|  |
|
|
Epoxy 5 min(Reference #1891)
QUIK-CURE™ epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour.127.6 Gram's (4.5oz)
Price: £4.21 £4.84 Including VAT at 15%
|  |
|
|
JB Weld(Reference #1892)
Tensile strenght 4000 psi after 24 hours Resistant to constant temperature up to 300 c Pliable for upto 25 minutes Permanently bonds metal, plastic, ceramic, wood, masonary can be drilled, filled, sanded, machined, tapped and painted 25 year shelf life once opened
Price: £5.06 £5.82 Including VAT at 15%
|  |
|
|
Kwik JB Weld(Reference #1893)
Don't Scrap it J-B Weld it! Tensile strenght 2500 psi Resistant to constant temperature up to 150 c Cure in four minutes. Full strenght in 20 minutes Bonds metal, plastic, ceramic, wood, masonary Can be drilled, filled, sanded, machined, tapped and painted
Price: £5.06 £5.82 Including VAT at 15%
|  |
|
|
JB Weld Industrial(Reference #60)
same specification as the standard JB Weld but in a larger quantity for commercial application.2 x 5oz tubes (141.8gr) 5 x the capacity of the standard pack- a saving of £6.35 (plus vat)
Price: £16.13 £18.55 Including VAT at 15%
|  |
|
